Jára
výkonný člen KLANu
- 137
V autech Mazda je spousta plastových dílů, které praskají a dá se je jen velmi obtížně sehnat. Napadlo někoho to tisknout na 3D tiskárně?
Našel jsem dost odkazů, kde se dají některé modely dílů vytisknout na 3D tiskárně. Podívejte se na odkazy, vybral jsem pár věcí pro Mazdu:
Našel jsem dost odkazů, kde se dají některé modely dílů vytisknout na 3D tiskárně. Podívejte se na odkazy, vybral jsem pár věcí pro Mazdu:
Clip for car hood gasket, Mazda by muxa4ever
I want it for a new car hood. The original parts can´t be removed from old hood, because the clip´s break. Original Mazda clip cost >2€. For Mazda Replaces: J001-56-741 Can be used in Mazda 626 GE (1991-1996), MX6,...
www.thingiverse.com
Mazda undercarriage 5.5mm diameter plastic nut by aumrysh
Noticed part of my Mazda 3 dangling when looking under the car. One of the plastic nuts had fallen off. I modeled and printed a replacement, now sharing with you in case the same happens :) The hole diameter is approx 5.4-5.5mm, though it should flex a bit to accomodate slightly larger or...
www.thingiverse.com
Mazda CX-3 sill clip by WheelerEngineering
Replacement trim clip which hold on the sill panels below the doors on a MAZDA CX-3 and possibly other MAZDA models. I printed these in Nylon for strength.
www.thingiverse.com
Mazda Oil Cap by mazhive
Again i lost my oilcap of my mazda pickup ,... its getting a habit.. not good... Printed it in ABS and it works perfect ! If you want to make your own design keep in mind the threads are m36 and the pitch is 4mm. It toke me a while to figure it out but once i had the thread i just copied the...
www.thingiverse.com
Mazda 6 Bord lower center console clip by PaulPanther
Editing Mazda 6 Bord lower center console clip
www.thingiverse.com
Mazda 6 Center Console light by RobsonM
This is a Mazda 6 2013 and later ambient light adapter for center console. Any modding is done at your own risk and I can't be hold accountable for any damage. Parts list: 1x LED 5mm 3V, preferably short one with 100 deg light cone 1x resistor 1k Ohm 2x M3x8mm bolt with locknut some wire, AWG...
www.thingiverse.com
mazda b2600 sunroof latch bracket by 1whoishere007
print PLA 212 extruder 62 bed
www.thingiverse.com
MX-5 / Miata - Antenna delete plug by szczawxd
Simple threaded antenna delete plug for our loved mx-5, use spacer in "trunk side" of plug for tighter fit. If you forgot to plug antenna hole during bodywork this is a great solution :)
www.thingiverse.com
Headlight Ring by redesigned
Headlight Bulb retaining ring designed for a 1999 Mazda B3000 with a type 9007 bulb. Will probably fit any vehicle with that bulb type and maybe some others. It is shorter than the original ring in order to accommodate an aftermarket led bulb but still works with the original.
www.thingiverse.com
Brake Pedal Bump Stop by TRE30
The bump stop at end of the travel on the Clutch and the Bake pedal, Original disintegrated and the Brake lights stayed on due to the pedal not actuating the Brake pedal switch. Fits Ford/Mazda Rangers pre-2007. (Mine is 2005 Supercab). I used SBS as it is more resilient than PLA.
www.thingiverse.com